News

Seek To See More - Full Size Shaker Fun - Picket Fence Studios

News

Seek To See More - Full Size Shaker Fun

by Lisa Tilson on Sep 29 2021
Hello there, it's Lisa here with you today to share a shaker card. I often make shakers but rarely a full size shaker so I thought I'd shaker it up a little! See what I did there? So here is what I came up with. It uses one of my favourite sets, Mermaid Dear, and I paired it with the A2 Tall Grass & Waves With Tile & Wood Floors stamp set for my background. To begin, I took some Tim Holtz Distress Watercolour cardstock and popped it into my MISTI. I repeat stamped the waves image from the A2 Tall Grass & Waves With Tile & Wood Floors set using Versmark Ink. I then applied white embossing powder and heat set. I smooshed some Distress Inks onto my glass media mat and spritzed them with some water and then took a paintbrush and applied them over the embossed waves area. I didn't go over the whole of the embossed area,but concentrated my colour in all areas but the top left corner. I used Mermaid Lagoon, Peacock Feathers and Cracked Pistachio - this is a great mix for water scenes, at least in my humble opinion. To build up the colour, I did a couple of layers, heat setting in between. I set the panel aside to air dry after the last layer had been added. This beautiful mermaid is from Mermaid Dear and she was stamped onto 80lb Neenah Solar White cardstock using PFS Black Hybrid Ink. I coloured her with Copic makers (the numbers are below) and then cut her out with the coordinating die before adhering her onto my watercoloured panel with wet adhesive. I then took an acetate sheet that was an inch larger than a normal A2 card and I cut a section from each corner so that I could wrap it around my watercoloured panel. I used double side tape to secure it at the back but left the top edge open so that I could add my sequins before finally sealing them in. My shaker mix was a combination of Mermaid Water Sequin Mix along with Spring Fling Sequin Mix. I added some of each into the front of the shaker and then sealed the top edge of the acetate at the back, again with strong double sided tape. The sentiment comes from Mermaid Dear and it was stamped onto black cardstock using sticky ink. I then added white embossing powder and heat set before trimming it out and adhering it onto the outside of the shaker panel with wet adhesive. To finish I added the shaker panel to a top folding A2 card. The movement of the sequins and the noise it makes is just fabulous! Copic numbers: Mermaid Skin (E70, E53, E51, E50, R20), Mermaid Hair (E55, E53, E51, E50), Mermaid Clothes (V17, V04, BG13, BG11), Puffer Fish (BV13, BV02, BV01) (BG32, BG13, BG11)  
Northern Lights Magic with Paper Glaze Lux - Picket Fence Studios

News

Northern Lights Magic with Paper Glaze Lux

by Rachelle Oltean on Sep 22 2021
1
Hello Crafters! It's Rachelle here and I've got a special card to share with you today: an easy CAS design featuring a background created with a brand new product from Picket Fence Studios...the Paper Glaze Lux Ombre "Nutcracker Ballet"!  Paper Glaze Lux is a mixed media glitter-based art medium, which blends heavy body mica with a glitter infusion, providing a MAXIMUM level of shine and thickness in a spreadable glitter glaze. Your application thickness allows you to determine the opacity level and so I experimented with painting a small, diluted amount directly onto black card stock and achieved a 'Northern Lights' Effect! You can see the base color of the pearly mica pigment body and the highlighted areas of glittery shine where the Lux was a bit thicker with color "C" from this Ombre collection! I was so excited with the result and this literally took me less than 5 minutes to create! After the Paper Glaze Lux panel was dry, I trimmed it down to 3.75" x 5" and attached it to the center of a top-folding A2 black card base. Using the "Santa's Snowy Hills" Die , I cut a panel from aqua card stock and trimmed off some of the silhouette, leaving a scattering of pine trees and the single house in the distance. This panel was cut to fit the width of the card front and adhered on top.  A sloped panel was cut to size from white card stock and the sentiment (from the "Winter Has Come To Town" Stamp Set) was stamped using my MISTI. I glued the small stamped/colored/die cut figure of the man carrying home his prize Christmas tree (from the "Winter Scene Building People") onto the sentiment panel, which was attached into place on the card front. A few "Spring Fling" Sequins finished up this clean-and-simple card! This design will be so easy to mass-produce and the effect of that painted Paper Glaze Lux is stunning in real life! I encourage you to stretch all of your Paper Glaze products by using them as painting mediums! Happy crafting and have a great day! Rachelle ♥